This electric scooter display is a waterproof 48V LCD display screen made by New Image as a replacement dashboard for the Kukirin G3 Pro electric scooter. It is the screen module that sits on the handlebar and shows the rider the information the scooter reports while riding. As a model-specific display rather than a universal panel, it is built to take the place of the original Kukirin G3 Pro display when the screen is damaged or no longer responding.
The unit arrives as a black display module with its mounting rings and a set of cable connectors, so it is prepared to drop into the position of the original part. Because it is sold as a Kukirin G3 Pro display, the fit and connectors are matched to that scooter instead of leaving you to adapt a generic screen.
This replacement screen focuses on the parts that matter when the dashboard needs replacing. The screen is housed in a black module and is described as a waterproof accessory, which suits a part that lives on the handlebar and is exposed to weather during normal riding.
The body of this display module is black with mounting rings on the housing and a set of cables that end in connectors. The mounting rings are what hold the screen in the handlebar clamp, and the connectors are the point where the display joins the rest of the scooter wiring. Because the connectors follow the layout the Kukirin G3 Pro was built around, the harness is the key reference when confirming that the replacement will line up with your scooter.
A waterproof housing is important for a dashboard because the screen is one of the few electrical parts left out in the open while riding. Keeping the 48V LCD display screen sealed helps it stand up to the rain and spray a scooter meets on the road. The confirmed structure here is simple: a sealed black screen module, its mounting rings and the cable connectors shown.
The confirmed details below describe this electric scooter display as supplied. Use them with your own scooter details when matching a replacement screen.
| Product | LCD display screen |
| Brand | New Image |
| System voltage | 48V |
| Suit for | Kukirin G3 Pro electric scooter |
| Type | E-scooter part replacement; dashboard display |
| Housing | Black module with mounting rings; waterproof |
| Connection | Cable connectors to the scooter wiring |
The 48V rating and the Kukirin G3 Pro fit are the two points that confirm this is the right 48V LCD display screen for your scooter. Because it is sold as a model-specific Kukirin G3 Pro display, the mounting and connectors are already matched, so the main step is confirming your scooter and checking that your existing connectors match the harness shown.
This electric scooter display is listed for the Kukirin G3 Pro, and its most common use is a dashboard repair. When a screen cracks, fogs, stops lighting up or loses its readout, swapping in a matching replacement screen is a direct way to bring the handlebar information back without replacing other parts of the scooter.
Repair shops that service Kukirin G3 Pro scooters keep this screen as stock so a display repair can be finished in a single visit. Resellers and fleet operators use the same approach, holding a small supply of this Kukirin G3 Pro display so a scooter is not left idle while a screen is sourced. In each case the mounting rings and prepared connectors make the swap a repeatable job.
Installing this display follows the same path as the original screen: disconnect the battery, release the old display from its handlebar mounting rings, then match each connector on the new harness to the same lines on the scooter. Keeping the cables in their original layout is the main step in a clean screen swap.
To confirm a correct fit, check that your scooter is a Kukirin G3 Pro and that your existing connectors match the harness shown, since this is a model-specific 48V LCD display screen rather than a universal panel. If your scooter differs, share your model and a photo of your current display and connectors so the right electric scooter display can be confirmed for your setup.
This Kukirin G3 Pro display is produced by New Image, a Shenzhen-based manufacturer with its own research, design and sales teams and OEM and ODM experience. For buyers who need branded or neutral packing, OEM and ODM options are available so the electric scooter display can be prepared to match a store or workshop presentation.
To move forward, send your scooter model, the quantity you need and your delivery destination. With those details the correct 48V LCD display screen and packaging can be confirmed for your order.
It is a 48V LCD display screen made for the Kukirin G3 Pro electric scooter. Confirm your scooter is a Kukirin G3 Pro and that your existing connectors match the harness shown before choosing this screen.
Yes. The screen is supplied as a waterproof accessory, which suits a dashboard that stays exposed on the handlebar during riding. Keeping the housing sealed helps the module stand up to rain and road spray.
The display is the handlebar screen that shows the information the scooter reports while riding. When the screen fails the rider loses that readout which is why a matching replacement display restores the dashboard.
Many riders complete the swap themselves because the module uses mounting rings and cable connectors. Disconnect the battery first, release the old screen, match each connector to the original line and keep the cables in their original layout. If you are unsure about the wiring a scooter technician can carry out the installation.
A model-specific screen is already matched to the scooter it was designed for so the voltage, mounting and connectors line up. A universal panel can differ in fit or wiring which is why matching the model is the safer choice.
EN
