Product Overview

The Sur Ron Hyper Bee handle grip (left side) is a direct-fit replacement component for the Sur Ron Hyper Bee electric dirt bike. Sold under the New Image brand with model number SUHB-05, this grip is designed specifically for the left position on the front handlebar. The component is new in condition and is intended for replace or repair use on the Hyper Bee platform.

The Sur Ron Hyper Bee is a compact electric dirt bike model in the Sur Ron lineup. The left handlebar position on the Hyper Bee carries no throttle mechanism, which means its grip differs in structure and mounting interface from the right-side grip. The SUHB-05 Sur Ron Hyper Bee handle grip addresses the left-side requirement directly and pairs with the corresponding right-side model SUHB-04 when a full handlebar grip set is needed. Selecting the correct side before ordering prevents misalignment with the brake lever bracket and handlebar end cap on the left side.

Key Features

The grip body is constructed from ABS plastic. ABS (acrylonitrile butadiene styrene) provides a balance of stiffness and impact resistance suited to electric motorcycle parts subject to vibration and occasional contact. The outer surface of the main grip zone features a hexagonal raised texture pattern visible in the product detail images. This geometric surface texture creates a mechanical grip interface between the rider's hand and the handlebar, maintaining control without relying on rubber softness or adhesion.

An anti-slip pattern is present at the end section of the grip, further reinforcing hold near the handlebar tip. A hand guard flange is integrated at the inboard end, positioned between the grip body and the handlebar clamp area to serve as a physical travel stop that limits hand movement toward the center of the bar. The dual-piece white inner sleeve, visible in the disassembled product image, forms the interior structure that contacts the handlebar tube surface. A black locking ring is shown alongside the grip in the product images; this ring provides the mechanical retention that secures the grip assembly on the handlebar once installed.

• ABS plastic body
• Hexagonal raised texture on grip surface
• Anti-slip pattern at end section
• Integrated hand guard flange at inboard end
• Dual-piece white inner sleeve
• Black locking ring shown in product images
• Gray color finish
• New Image brand, model SUHB-05

Construction and Material Details

ABS plastic is a common structural material in electric motorcycle parts because it holds dimensional accuracy under repeated loading and resists deformation at typical ambient temperatures. In this Sur Ron Hyper Bee handle grip, the ABS shell houses the dual-piece inner sleeve and provides the outer texture surface. The hexagonal pattern raises the grip contact points above the base surface level, increasing friction without a soft-compound overmold. This geometry-based grip approach keeps the outer profile consistent even after prolonged use, since there is no rubber layer to compress or tear.

The dual-piece inner sleeve consists of two fitted sections visible when the grip end cap is separated. These sleeve pieces align inside the grip shell and interface directly with the handlebar tube. The locking ring, which fits over the inboard end of the grip, engages a retention groove to prevent the assembly from rotating or sliding axially on the handlebar. Both the inner sleeve and locking ring are functional structural components; neither is decorative.

Specifications

The 13 cm overall length and 5.5 cm end width are taken from the dimension label visible in the product image gallery. The 48.4 g net weight is marked as "N.W." in the same dimension image. These figures describe the grip component itself. Confirm the handlebar tube diameter at the installation point matches the inner sleeve bore before ordering.

Application and Compatibility

This component is designed for the Sur Ron Hyper Bee electric dirt bike. The Hyper Bee is a distinct model in the Sur Ron range, separate from the Light Bee and Storm Bee in frame geometry and component specifications. Using the correct model-specific part is particularly important for handlebar grips because mounting geometry, grip length, and end cap dimensions can vary between Sur Ron models even when the parts appear similar.

The SUHB-05 is the left-side Sur Ron Hyper Bee handle grip. The Sur Ron Hyper Bee left grip covers the non-throttle handlebar end, which typically carries the brake lever and any left-side controls. Riders replacing a worn, cracked, or missing grip on the left front handlebar of the Hyper Bee will find the SUHB-05 directly matches that position. This electric dirt bike handlebar grip can be ordered as a standalone replacement, allowing single-side replacement without replacing the full handlebar assembly.

The grip is also applicable as a Sur Ron replacement grip in maintenance contexts where the factory grip has deteriorated or been removed. Because the ABS shell maintains its shape over time, it is suited to riders who need a structurally stable grip rather than a soft-compound alternative. Riders working on multiple Hyper Bee units can source this grip as a consistent part number for left-side handlebar maintenance across their fleet.

Installation Guidance

Before installing this Sur Ron Hyper Bee left grip, verify the following:

• Vehicle model: Confirm the target vehicle is a Sur Ron Hyper Bee. Other Sur Ron models use different grip specifications; the SUHB-05 model number applies specifically to the Hyper Bee left-side handlebar position.
• Side orientation: The SUHB-05 is the left-side grip. On the Hyper Bee, the left handlebar end carries the brake lever assembly. Installing a left-side grip in the right-side throttle position will result in a misfit because the internal sleeve geometry and end cap orientation are side-specific.
• Handlebar tube diameter: Confirm the handlebar outer diameter at the grip end matches the inner sleeve bore of the SUHB-05. The dual-piece sleeve must seat fully around the tube for the locking ring to engage the retention groove correctly.
• Locking ring engagement: After sliding the grip onto the handlebar tube, position the black locking ring over the inboard grip end and engage the retention groove. The locking ring must seat fully to prevent grip rotation and axial movement under load. A loose locking ring will allow the grip to shift during riding.

Standard grip installation for this type of component involves sliding the assembled grip sleeve over the handlebar tube from the end, seating the inboard hand guard flange against the bar clamp or control bracket, and securing the locking ring. No adhesives or special tools are specified for the SUHB-05 grip. If the sleeve does not slide onto the tube smoothly, check the tube diameter against the sleeve bore rather than forcing the fit, as forcing can damage the ABS sleeve sections.

Packaging and Inquiry

This Sur Ron Hyper Bee handle grip is listed as a single replacement component. The product images show the grip body and a black locking ring together. For confirmation of exact package contents, minimum order quantities, or lead time before placing a bulk inquiry, contact us directly through the inquiry form on this page.

Include the vehicle model (Sur Ron Hyper Bee), the required handlebar side (left), and your quantity in the inquiry message to receive accurate pricing and availability information for this electric dirt bike handlebar grip.